Skip to content
Quality, standards & complianceAerospace

Check EASA Form 1 at goods receipt

demi reads every release certificate, checks it against purchase order and delivery note and proposes parts with gaps for quarantine.

Today

In aviation a part may only be installed with a matching release certificate, usually EASA Form 1. At goods receipt someone checks by hand whether part number, revision, quantity, serial numbers and status match the purchase order and delivery note, whether the right block is ticked and signed and whether the issuer holds a valid approval. With scans, distributor copies and dozens of blocks per certificate, a transposed digit or a missing signature slips through. Often it shows only at installation or in an audit, and until it is cleared the part cannot be used.

An example

At Rennhardt Aerospace 14 deliveries with EASA Form 1 arrive at goods receipt on a Tuesday. The agent checks them all within minutes and passes eleven without findings to the inspector. For 24 reading lights a distributor delivers for cabin linings, two serial numbers appear on the certificate but not on the delivery note, and one of them was already booked in April with another delivery. For 40 Ti6Al4V fittings from a supplier the certificate states Rev B where Rev C was ordered, and a third delivery lacks the signature in block 13b. The agent proposes the three items for quarantine and drafts the queries to distributor and suppliers. The inspector quarantines the parts, and the quality manager decides whether the duplicate serial number is reported as a suspected unapproved part.
Fictional company, typical workflow.

Your data, wherever it lives

Today release certificates sit as paper in the delivery box, as scans at goods receipt or as PDFs in the mailbox, orders and receipts in the ERP, and the approved supplier list in the QMS. demi reads, understands and links them per delivery and serial number, with your access rights. AI checks every certificate block by block in seconds and proposes parts with gaps for quarantine, and the inspector decides.

Where the data lives today

  • Scans & paper
  • PDFs
  • E-mails
  • ERP
  • QM system
Data LayerOne view of everything, with your rights

How demi solves it

Three layers in this order: connect the data first, then the rights, then the AI.

  1. 1 · ConnectData Layer

    Data sources in this case: scans and PDFs of the certificates, delivery notes from the mailbox, purchase orders and receipts in the ERP or maintenance system, and the approved supplier list with its approvals in the QMS. demi replaces nothing and links, per delivery, certificate, order line, delivery note, label and supplier. Every serial number knows its earlier receipts, and every form tracking number the deliveries it has already appeared on.

  2. 2 · PermitPermission Layer

    Certificates and inspection results are visible to goods receipt, quality and purchasing; prices on the order stay with purchasing. Only an authorized inspector may release or quarantine a part, and quality management decides whether a suspicion is reported to the authority; every decision is recorded with name and time.

  3. 3 · ActIntelligence Layer

    The agent reads every certificate block by block, including skewed scans and handwritten entries, and compares part number, revision, quantity, serial numbers and status with order and delivery note. It checks whether block 13a for new parts or 14a for maintained parts fits, whether signature, name, date and approval number are present and whether the issuer is on your approved supplier list. Your quality team sets the inspection rules; the agent applies them the same way to every delivery and proposes, and the inspector decides.

How it runs

  1. 1

    The delivery arrives; certificate and delivery note are scanned or are already in the mailbox as PDFs.

  2. 2

    demi reads every block of the EASA Form 1 and finds the matching order line in the ERP.

  3. 3

    The agent compares part number, quantity, serial numbers, status and signature and checks the issuer against your supplier list.

  4. 4

    Deliveries without findings go for release; parts with gaps go to the inspector as a quarantine proposal naming block and deviation.

  5. 5

    The inspector releases or quarantines; the ERP booking and the query to the supplier follow her decision.

What changes

  • Every certificate checked block by block before the part goes into stock

  • Duplicate serial numbers and doubtful copies surface at goods receipt, not at installation

  • Inspection evidence per part ready for customers and audits

What does it bring you?

Check it with your own numbers

Every starting value is an assumption you can change. The calculation sits right below, step by step.

Assumption, editable

Your numbers

Result

+180 hfreed per year

Assumptions and calculation

demi reads each certificate and checks it against order and delivery note; the inspector decides.

12 min → 8.4 min per case

How does it run today?

What is already digital saves less: the factor lowers the share demi brings.

How we calculate

250 release certificates × 12 min × 30% × 1.0 (manual) × 12 months = 10,800 min = 180 h

Value per year, before demi costs

Freed per year+180 h

Assumption: labor cost of $48.62 per hour in US manufacturing in June 2026 (BLS), plus workplace, IT and overhead.

= Value per year, before demi costs

+$11,700

gained per year

180 h ÷ 1,760 h per role = 0.1 full-time roles

An estimate, not a promise. The starting values are assumptions for an industrial company with 150 to 500 people.

Combine with more cases and get the package

Questions about this use case

Which certificates does demi read besides EASA Form 1?

Also its US counterpart, FAA Form 8130-3, dual EASA and FAA releases, certificates of conformity from manufacturers and distributors, and mill certificates for raw material. For each type your quality team sets which blocks are checked against which data. Illegible blocks are shown marked instead of guessed.

Does demi detect forged release certificates?

demi detects warning signs, not forgery with certainty: a serial number already in the house, a form tracking number with different quantities or serial numbers than last time, an issuer without a valid approval, or a layout that differs from earlier certificates of the same issuer. The agent collects the evidence and proposes quarantine. Whether a suspicion is reported is decided by your quality management.

How does demi know whether an issuer is approved?

From your approved supplier list in the QMS, with approval number, scope and validity. The number on the certificate must match the issuer and the list. When an approval expires or its scope changes, your quality team updates the list, and from then on the agent checks against the new status.

What happens to a quarantined part?

It goes to the quarantine store and is booked as blocked in the ERP as soon as the inspector has decided. After her release the agent sends the query with block, deviation and scan to the supplier and follows up the answer. A corrected certificate is checked like the first one, and the inspector then releases the part or returns it.

See this case with your data

In the demo we show you the workflow on your own systems.

Your configurator

No use cases yet

Your configurator is still empty

Add a use case from any card or case page and see what it brings per year, with the calculation. Free, no sign-up, no commitment: try it out and change any number.

Browse use cases