Today
At the furnace the melter has a few minutes to decide: the sample is analysed, the spectrometer printout lies in front of him, and carbon, silicon or manganese may still need correcting before tapping. Which limits apply is written in the material standard, the customer specification and the work instruction, and he works out the addition in his head or with an old spreadsheet. Which melt went into which casting batch and which certificate is pieced together by hand later.
An example
In the foundry of Rabenhammer Präzisionsteile, 4.2 t of melt sit in medium-frequency induction furnace 2, intended for housings GH-3310 in EN-GJS-400-18-LT. The first sample shows 3.48 % carbon and 0.22 % manganese; the customer specification allows at most 0.20 % manganese, the in-house work instruction 0.30 %. The agent flags the manganese and proposes diluting with 1,000 kg of low-manganese pig iron: by its mass balance the melt ends up at 0.18 % manganese and 3.62 % carbon, with no extra carburiser. The melter adds it, the check sample confirms 0.18 % manganese, and the head of the lab releases the melt. The analysis is then attached to casting batch G-5512 and to the 3.1 inspection certificate for 120 housings.
Your data, wherever it lives
What is in a melt sits in many places today: analyses in the spectrometer and as a printout at the furnace, charge make-up and charge materials in the ERP, standards and customer specifications as PDFs, casting batches in the MES, inspection certificates in the CAQ. demi reads, understands and links them per melt, with your rights. The AI checks an analysis against every applicable limit in seconds and works out the correction, and melter and lab decide.
Where the data lives today
- Machines & sensors
- Databases
- ERP
- PDFs
- MES
- QM system
How demi solves it
Three layers in this order: connect the data first, then the rights, then the AI.
- 1 · ConnectData Layer
Data sources in this case: analyses from the spectrometer, furnace contents and temperatures from the furnace control, charge make-up and charge materials in the ERP, material standards and customer specifications as PDFs, casting batches and jobs in the MES and inspection certificates in the CAQ. demi replaces nothing and links every analysis with furnace, melt, material, job and the castings poured from it. For each melt you see what it contained, what was corrected and where it went.
- 2 · PermitPermission Layer
Analyses and corrections are visible to the melt shop, lab and quality; customer specifications only to the people working for that customer. Correcting, tapping and releasing stay with the melter and the head of the lab; demi writes to the inspection certificate only after their release, and every decision is recorded.
- 3 · ActIntelligence Layer
The agent checks every element of the analysis against the strictest applicable limit from standard, customer specification and work instruction. If a value is off, it works out the addition in kilograms from furnace contents, analysis and the recovery of the alloying agents, including dilution when an element cannot be removed. The calculation is a fixed mass balance, not an estimate; the language model only explains why a correction is due.
How it runs
- 1
The melt sample runs through the spectrometer and the analysis goes straight to demi.
- 2
The agent checks each element against the strictest applicable limit from standard, customer specification and work instruction.
- 3
If an element is off, it works out the addition or dilution in kilograms, using furnace contents and recovery.
- 4
The melter corrects, the check sample confirms the analysis, and the head of the lab releases the melt.
- 5
The released analysis is attached to casting batch, job and inspection certificate, with no copying by hand.
What changes
Fast, sound decisions at the furnace
Less scrap from wrong chemistry
Every melt traceable all the way to the inspection certificate
What does it bring you?
Check it with your own numbers
Every starting value is an assumption you can change. The calculation sits right below, step by step.
Your numbers
Result
+144 hfreed per year
Assumptions and calculation
demi checks every analysis against all applicable limits and works out the correction; you release the melt.
15 min → 10.5 min per case
How we calculate
160 melts × 15 min × 30% × 1.0 (manual) × 12 months = 8,640 min = 144 h
Value per year, before demi costs
Freed per year+144 h
Assumption: labour cost of €49.50 per hour in German manufacturing in 2025 (Destatis), plus workplace, IT and overheads.
= Value per year, before demi costs
+€9,360
gained per year
144 h ÷ 1,760 h per role = 0.1 full-time roles
An estimate, not a promise. The starting values are assumptions for an industrial company with 150 to 500 people.
Combine with more cases and get the packageQuestions about this use case
How does the analysis get from the spectrometer to demi?
Through the export your spectrometer already has, usually one file per sample on the network drive or a database in the lab. Furnace contents and temperature come from the furnace control or are entered on a tablet at the furnace. We clarify how the connection works in your plant when we talk.
How does the agent know the limits for each material?
From your material standards, customer specifications and work instructions, which demi reads and combines per material and customer. Where several limits apply, it takes the strictest and shows which document it comes from.
How accurate is the calculated addition?
As accurate as the furnace contents, the analysis and the recovery of your alloying agents. The agent computes the mass balance exactly and learns the actual recovery from the check samples of earlier melts. A check sample after the correction remains mandatory.
Does this work for cast steel, aluminium or copper alloys too?
Yes. The principle stays the same: analysis against the strictest limit, correction by mass balance, release by the lab. Elements, alloying agents and limits come from the documents for your material.
