Skip to content
Quality, standards & complianceMetal & MachiningPlastics & PackagingTool & Mold MakingAutomotive Suppliers+2

Check measurement reports against the drawing

The drawing gives you the inspection plan, and every value out of tolerance is flagged.

Today

Inspection plans are typed up from the drawing, and measurement reports are checked by eye. With many characteristics, a value out of tolerance slips through easily. Often the customer is the first to notice.

An example

A measurement report for flange 300-4410 in 42CrMo4 covers 42 characteristics. The agent finds the Ø 40 h6 spigot at the upper limit and a flatness value out of tolerance, and opens a deviation at Rabenhammer Präzisionsteile with inspector, gauge and drawing revision.
Fictional company, typical workflow.

Your data, wherever it lives

Today drawings sit in CAD and PLM, control plans and FMEA in the QM system or in spreadsheets, and measurement reports arrive as PDFs or as exports from the measuring machine. demi reads, understands and links them per part and characteristic, with your rights. The AI derives the inspection characteristics with their tolerances from the drawing and checks every measured value in seconds instead of twenty minutes of manual comparison per report, and quality assurance releases and decides on deviations.

Where the data lives today

  • CAD & drawings
  • PLM
  • QM system
  • Office files
  • PDFs
  • Machines & sensors
Data LayerOne view of everything, with your rights

How demi solves it

Three layers in this order: connect the data first, then the rights, then the AI.

  1. 1 · ConnectData Layer

    The case needs data from the PLM, QMS, CAQ and spreadsheets. demi replaces nothing and links drawings, control plans, FMEA, measurement reports and gauges per part; each characteristic is one record with nominal value, tolerance and every measurement. demi writes back only after approval.

  2. 2 · PermitPermission Layer

    Quality releases inspection plans. Every result is recorded with inspector and gauge, and deviations go to the right owner.

  3. 3 · ActIntelligence Layer

    The agent reads characteristics and tolerances from the drawing, drafts the inspection plan from the control plan and FMEA and compares every measured value with its tolerance. The comparison is plain arithmetic, not an estimate, and each characteristic points to its place on the drawing.

How it runs

  1. 1

    Link drawing, control plan and FMEA to the part

  2. 2

    The agent proposes characteristics with tolerances

  3. 3

    Quality releases the inspection plan

  4. 4

    Upload the report or take it from the measuring software

  5. 5

    demi checks every value and opens deviations

What changes

  • Complete inspection plans

  • Every deviation listed against its tolerance

  • Faster release

What does it bring you?

Check it with your own numbers

Every starting value is an assumption you can change. The calculation sits right below, step by step.

Assumption, editable

Your numbers

Result

+320 hfreed per year

Assumptions and calculation

demi derives the characteristics from the drawing and checks each reading against tolerance; you release.

20 min → 12 min per case

How does it run today?

What is already digital saves less: the factor lowers the share demi brings.

How we calculate

200 inspection reports × 20 min × 40% × 1.0 (manual) × 12 months = 19,200 min = 320 h

Value per year, before demi costs

Freed per year+320 h

Assumption: labor cost of $48.62 per hour in US manufacturing in June 2026 (BLS), plus workplace, IT and overhead.

= Value per year, before demi costs

+$20,800

gained per year

320 h ÷ 1,760 h per role = 0.2 full-time roles

An estimate, not a promise. The starting values are assumptions for an industrial company with 150 to 500 people.

Combine with more cases and get the package

Questions about this use case

Can demi read tolerances from drawings?

Yes, from PDF and CAD drawings with dimensions, fits and geometric tolerances. Every characteristic it finds points to its place on the drawing. Anything not clearly legible is flagged for review before it goes into the plan.

Does it work with our measuring software's exports?

Usually yes: CSV, spreadsheet and PDF exports from coordinate measuring machines and hand gauges can be connected. demi maps the values to the characteristics in the plan. If a mapping is unclear, the agent asks instead of guessing.

Does demi use our control plan and FMEA?

Yes. The agent takes inspection frequency, method and special characteristics from the control plan and FMEA. So the draft matches what you have already decided.

Who decides on a deviation?

Quality does. demi opens the deviation with all the data and suggests the next step. Whether it is a concession, rework or a hold is decided by a person, and the record keeps it.

See this case with your data

In the demo we show you the workflow on your own systems.

Your configurator

No use cases yet

Your configurator is still empty

Add a use case from any card or case page and see what it brings per year, with the calculation. Free, no sign-up, no commitment: try it out and change any number.

Browse use cases