Skip to content
Service & spare partsPumps & ValvesWater & EnvironmentMachinery & Plant EngineeringConveying & Intralogistics+3

Hands-free hotline for field technicians

Gloves on, at the unit: the technician calls, gives the serial number and hears the test steps and values for exactly this unit.

Today

With gloves on and both hands on the equipment, nobody scrolls through a 400-page manual. So the technician works from memory, guesses a tightening torque or calls the one colleague who knows the unit and is out on a site himself. On top of that, values differ by year of build and design, and nobody on site knows for sure which revision of the instructions applies.

An example

A service technician at Wattaris stands in a substation in front of a 630 kVA transformer, 20/0.4 kV, vector group Dyn5, gloves on and meter in hand. He calls on his headset and gives the serial number TR-19-0832. demi recognizes the design with a conservator and reads out the steps for putting it back into service from the maintenance instructions of this revision, one at a time; after each one he says “next”. At the low-voltage terminals he asks for the tightening torque and hears the value from the assembly instructions, with the page. He reports with a photo that the earthing point sits differently from the drawing; the responsible design engineer calls back twenty minutes later.
Fictional company, typical workflow.

Your data, wherever it lives

What a technician needs to know at the unit sits today in PDF manuals and assembly instructions in the DMS, in drawings and changes in the PLM, in the build state of the serial number in the ERP, in old service cases and in scanned paper documents. demi reads, understands and links it per unit, with your rights. On the phone the technician hears in seconds what would otherwise mean leafing through pages or calling someone, and he decides what to do at the unit.

Where the data lives today

  • Phone & voice
  • PDFs
  • DMS & archive
  • PLM
  • ERP
  • Tickets
  • Scans & paper
Data LayerOne view of everything, with your rights

How demi solves it

Three layers in this order: connect the data first, then the rights, then the AI.

  1. 1 · ConnectData Layer

    Data sources in this case: phone, PDF manuals, DMS, PLM, ERP, service tickets and scanned documents. demi replaces nothing and links every serial number with its design and build state, with the maintenance and assembly instructions in the right revision, drawings, changes and earlier service cases. Old scanned paper documents become searchable too.

  2. 2 · PermitPermission Layer

    demi recognizes technicians and fitters by mobile number and PIN and reads out only documents they may see; service partners hear only what is released for their units. Safety-relevant steps are read word for word from the approved instructions, never paraphrased. Every call is recorded with serial number, questions and sources.

  3. 3 · ActIntelligence Layer

    The agent identifies the unit and revision from the serial number, finds the right passage in the documents and reads out test steps, tightening torques and settings one at a time, at the technician's pace. It quotes values word for word from the source, with document and page. If it finds no answer, it says so and forwards the question with a photo to the responsible design engineer.

How it runs

  1. 1

    The technician calls the demi number on a headset or hands-free and gives the serial number.

  2. 2

    demi identifies the unit, its design and build state and says which instructions apply in which revision.

  3. 3

    He says what he is about to do; demi reads the steps out one by one and waits for “next”, “repeat” or a question.

  4. 4

    If an answer is missing, he sends a photo and demi forwards the question with the serial number to the responsible design engineer.

  5. 5

    After the call, steps, values and sources arrive as a message, and the service case is updated with the call record.

What changes

  • Both hands stay on the equipment

  • The right value for exactly this design, not a guess

  • Fewer calls to the one expert who knows everything

What does it bring you?

Check it with your own numbers

Every starting value is an assumption you can change. The calculation sits right below, step by step.

Assumption, editable

Your numbers

Result

+225 hfreed per year

Assumptions and calculation

demi reads out steps and values for exactly this unit; the technician works and decides.

15 min → 10.5 min per case

How does it run today?

What is already digital saves less: the factor lowers the share demi brings.

How we calculate

250 questions from the field × 15 min × 30% × 1.0 (manual) × 12 months = 13,500 min = 225 h

Value per year, before demi costs

Freed per year+225 h

Assumption: labor cost of $48.62 per hour in US manufacturing in June 2026 (BLS), plus workplace, IT and overhead.

= Value per year, before demi costs

+$14,625

gained per year

225 h ÷ 1,760 h per role = 0.1 full-time roles

An estimate, not a promise. The starting values are assumptions for an industrial company with 150 to 500 people.

Combine with more cases and get the package

Questions about this use case

Does this work with noise in the hall or at the unit?

Yes, with a noise-canceling headset, as many technicians wear anyway. If demi does not catch a number clearly, it asks again instead of guessing, and it repeats serial numbers and values for confirmation.

How does demi know which revision of the instructions applies?

From the serial number: demi knows from the ERP and PLM the design, build state and later changes of the unit and picks the document that belongs to it. If the unit was modified later, demi says so right at the start.

What happens if the documents have no answer?

demi says so openly and passes the question on, with the serial number, a photo and what the technician has already checked, to the responsible design engineer or expert. The answer comes back as a call or message and, once approved, is ready for the next identical question.

Can assembly fitters call too, in the workshop or at the customer's site?

Yes. Fitters ask about revision, tightening torque or mounting position for their serial number, and demi answers from the drawing, build state and changes. Open questions go to engineering with a photo, instead of someone hunting for the drawing or guessing.

See this case with your data

In the demo we show you the workflow on your own systems.

Your configurator

No use cases yet

Your configurator is still empty

Add a use case from any card or case page and see what it brings per year, with the calculation. Free, no sign-up, no commitment: try it out and change any number.

Browse use cases