Skip to content
Planning & productionWater & EnvironmentWaste & RecyclingChemicals & Process IndustryFood & Beverage

Treatment plant: aeration with less power

demi uses control system data to show where the blowers deliver more air than the load needs and proposes new setpoints for approval.

Today

Aerating the activated sludge tanks often takes half or more of a treatment plant's power. Its setpoints were set at commissioning and are rarely checked again, although the load varies widely over the day, the week and the seasons. At night and at weekends the blowers often blow in as much air as at peak time. The data for this sits in the control system, but nobody has the time to compare months of trends with the effluent values.

An example

Aldevo Wassertechnik runs a municipal treatment plant for 40,000 population equivalents under an operating contract. The agent analyses three months of control system data: between 11 pm and 5 am the ammonium at the outlet of the aeration tanks is below 0.3 mg/l, yet three blowers keep the oxygen at 2.0 mg/l at night as well. It proposes lowering the night setpoint to 1.2 mg/l and coupling the daytime setpoint to the ammonium value, and expects about 70,000 kWh less power a year, with the effluent staying well clear of the 10 mg/l ammonium nitrogen limit. The plant manager approves the night curve for a four-week trial; afterwards the agent compares effluent values and power use.
Fictional company, typical workflow.

Your data, wherever it lives

Your treatment plant's data lives today in the control system and its historian, power values in the meters and their exports, lab values and the operating log in spreadsheets, the discharge permit and blower data sheets as PDFs. demi reads, understands and links them per tank and hour, with your rights. The AI finds the hours with too much air in minutes instead of in a yearly review, and plant management decides on new setpoints.

Where the data lives today

  • Machines & sensors
  • Databases
  • Office files
  • PDFs
Data LayerOne view of everything, with your rights

How demi solves it

Three layers in this order: connect the data first, then the rights, then the AI.

  1. 1 · ConnectData Layer

    Data sources in this case: the control system and its historian with oxygen, ammonium, nitrate, inflow, air flow, valve positions and blower power, plus power meters, lab values and the operating log. demi replaces nothing and puts everything on one timeline per tank and hour, together with the effluent limits from the discharge permit.

  2. 2 · PermitPermission Layer

    Operators and energy management see the plant data; the lab releases lab values. Only the authorized person changes setpoints in the control system; demi writes nothing to the controls. Every proposal and every approval is recorded.

  3. 3 · ActIntelligence Layer

    The agent compares air flow and oxygen with the actual load from ammonium and inflow and finds the hours in which more air is blown in than the biomass needs. It proposes setpoints per time of day or a coupling to the ammonium value, works out the power saving from the meter data and checks every proposal against past effluent values and the permit limits. The numbers come from the measurements; the language model only explains the proposal.

How it runs

  1. 1

    demi reads the trends of oxygen, ammonium, nitrate, inflow, air flow and blower power from the control system.

  2. 2

    The agent lines them up with power meters, lab values and the operating log, per tank and hour.

  3. 3

    It shows when aeration delivers more air than the load needs and how much power that costs.

  4. 4

    From this it proposes new setpoints, checked against past effluent values and the permit limits.

  5. 5

    The plant manager approves the change; the agent then follows effluent and power use.

What changes

  • Less power for aeration

  • Setpoints that match the actual load

  • Effluent values watched with every change

What does it bring you?

Check it with your own numbers

Every starting value is an assumption you can change. The calculation sits right below, step by step.

Assumption, editable

Your numbers

Result

+81 hfreed per year

Assumptions and calculation

demi analyses oxygen, ammonium and blowers and proposes setpoints; you approve them.

45 min → 31.5 min per case

How does it run today?

What is already digital saves less: the factor lowers the share demi brings.

How we calculate

30 daily reviews × 45 min × 30% × 1.0 (manual) × 12 months = 4,860 min = 81 h

Value per year, before demi costs

Freed per year+81 h

Assumption: labor cost of $48.62 per hour in US manufacturing in June 2026 (BLS), plus workplace, IT and overhead.

= Value per year, before demi costs

+$5,265

gained per year

An estimate, not a promise. The starting values are assumptions for an industrial company with 150 to 500 people.

Combine with more cases and get the package

Questions about this use case

Does demi intervene in the plant's controls?

No. demi reads the data from the control system and its historian and makes proposals. The authorized person changes setpoints in the control system, as today, and the change is recorded together with the proposal.

How does the agent know how much air the biomass needs?

From the interplay of ammonium, nitrate, oxygen, inflow and air flow over weeks and months. It compares hours with similar load and shows when the same treatment result was reached with less air. It uses lab values to check the online measurements.

What happens in winter, when nitrification slows down?

The agent takes the water temperature into account and proposes setpoints per season. Your plant management sets minimum oxygen values, and it proposes nothing below them. If ammonium rises after a change, it reports this at once and shows the previous setpoint.

Does this also work for an industrial treatment plant?

Yes. Food, chemical and paper plants with their own biological treatment see load peaks from production, for example after cleaning or product changes. demi also links the production plan, so that aeration matches the load that is coming.

See this case with your data

In the demo we show you the workflow on your own systems.

Your configurator

No use cases yet

Your configurator is still empty

Add a use case from any card or case page and see what it brings per year, with the calculation. Free, no sign-up, no commitment: try it out and change any number.

Browse use cases