Skip to content
Marketing & campaignsPumps & ValvesElectronics & SensorsWater & EnvironmentMachinery & Plant Engineering+3

A personal savings calculation for every existing customer

Every customer sees what a replacement or retrofit saves on their own equipment, calculated from its operating data.

Today

Efficiency campaigns promise “up to a third less energy” across the board, but every customer wants to know what their own pump, drive or ventilation unit costs them. You have the data: year of build and motor in the ERP, duty point and running hours in service reports, curves in the PLM. Nobody works it through for hundreds of units, so everyone gets the same brochure, and most put it aside.

An example

Hartwig & Brunn Pumpenwerk plans an efficiency campaign for KP centrifugal pumps with IE2 motors. In the ERP the agent finds 214 such pumps built between 2009 and 2014 at 87 customers that are still running according to service tickets. A municipal utility runs a KP DN 100 from 2009 in its district heating network, 7,000 hours a year according to the last service report, about 5,000 of them throttled to 70 instead of 120 m³/h. Its one-pager shows two options: retrofit a variable speed drive, about 50,000 kWh less per year, around 9,000 euros at the 18 cents per kWh the utility named in its last inquiry; or a new KP DN 100 with an IE4 motor and drive, about 55,000 kWh less. For 31 customers the running hours are missing, and the agent proposes a short e-mail asking for the hour meter reading. Sales checks the ten largest calculations itself and approves the mailings.
Fictional company, typical workflow.

Your data, wherever it lives

What a unit consumes today is recorded in many places: year of build, motor and serial number in the ERP, duty point and running hours in service reports, tickets and the data of connected units, curves in the PLM, energy prices in inquiries and e-mails, contacts in the CRM. demi reads, understands and links them, with your rights. The AI works through every unit within minutes, where application engineering needs hours today, and your sales team approves what goes out.

Where the data lives today

  • ERP
  • CRM
  • Tickets
  • Machines & sensors
  • PLM
  • E-mails
Data LayerOne view of everything, with your rights

How demi solves it

Three layers in this order: connect the data first, then the rights, then the AI.

  1. 1 · ConnectData Layer

    The case needs data from the ERP, CRM, ticket system and PLM and, where units are connected, their operating data. demi replaces nothing and links, per unit, serial number, year of build, motor and efficiency class, duty point and running hours from service reports, curves and retrofit kits from the PLM, and the electricity price the customer stated in inquiries or e-mails. If a value is missing, the unit shows it.

  2. 2 · PermitPermission Layer

    A customer's units, prices and energy data are visible only to their account manager and sales; no customer sees another's figures. Only contacts that may be written to are contacted, and the account manager can hold any customer back. A mailing goes out only after sales approves it, and the approval is logged.

  3. 3 · ActIntelligence Layer

    The agent selects the units where a replacement or retrofit may pay off and calculates consumption today and afterwards for each. The calculation follows a fixed method with curves, efficiencies and running hours; the language model only writes the mailing and the one-pager. Every figure carries its origin: measured, from a service report or assumed. Where the data is too thin, the agent proposes a question to the customer instead of guessing.

How it runs

  1. 1

    Marketing defines the campaign: product lines, years of build and solutions, such as a more efficient motor, a variable speed drive or a new unit.

  2. 2

    The agent finds the matching units in the ERP and service history and checks which are still running according to tickets.

  3. 3

    For every unit it calculates consumption, cost and payback today and after the upgrade, each figure with its origin.

  4. 4

    It drafts a mailing and a one-pager per customer; where data is missing, it proposes a short question instead.

  5. 5

    Sales checks the largest calculations itself and approves; replies land as a task with the responsible account manager.

What changes

  • Customers get their own calculation instead of a brochure

  • The units with the biggest lever come first

  • Sales starts conversations with documented figures

What does it bring you?

Check it with your own numbers

Every starting value is an assumption you can change. The calculation sits right below, step by step.

Assumption, editable

Your numbers

Result

+192 hfreed per year

Assumptions and calculation

demi calculates each unit from its own data and drafts the mailing; sales checks and approves.

2 h → 1.2 h per case

How does it run today?

What is already digital saves less: the factor lowers the share demi brings.

How we calculate

20 savings calculations × 2 h × 40% × 1.0 (manual) × 12 months = 192 h

Value per year, before demi costs

Freed per year+192 h

Assumption: labor cost of $48.62 per hour in US manufacturing in June 2026 (BLS), plus workplace, IT and overhead.

= Value per year, before demi costs

+$12,480

gained per year

192 h ÷ 1,760 h per role = 0.1 full-time roles

An estimate, not a promise. The starting values are assumptions for an industrial company with 150 to 500 people.

Combine with more cases and get the package

Questions about this use case

Where do the running hours and duty point come from?

From service reports and commissioning records, from maintenance and spare part tickets and, where units are connected, from their operating data. Every value appears on the one-pager with its source and date. If it is missing, the agent does not calculate with an estimate but proposes a question to the customer.

Which energy price does demi use?

The price the customer stated, for example in an inquiry or an e-mail. If none is known, the agent uses an assumed value set by your sales team and states it visibly. The customer can then follow the calculation with their own price.

Is the calculated saving a commitment?

No. The one-pager shows a calculation with named assumptions, not a commitment. Where the exact value matters, the agent proposes a measurement on site, and application engineering checks the calculation before it becomes a quote.

What happens with the customers' replies?

Every reply and question lands as a task with the responsible account manager, together with the unit and the calculation. If a customer sends the missing running hours, the agent recalculates; if they ask for a quote, sales takes the values straight over.

See this case with your data

In the demo we show you the workflow on your own systems.

Your configurator

No use cases yet

Your configurator is still empty

Add a use case from any card or case page and see what it brings per year, with the calculation. Free, no sign-up, no commitment: try it out and change any number.

Browse use cases