Today
A new injection mold usually needs several correction loops before its parts are within tolerance, and each loop costs about a week: the mold goes back to the toolroom, is reworked, tried out again and measured again. The findings of a try-out are scattered: the CMM report, photos of sink marks and flash, the setting sheet from the molding machine and notes on the printout. Whoever writes the correction list gathers it all by hand and rarely knows how the same dimension behaved on earlier molds. So corrections come out too small, too large or in the process instead of the steel, and the same mistakes repeat.
An example
Norvelta runs the first try-out of an 8-cavity mold in 1.2343 for a connector housing in PA6 GF30. The measurement report shows 14 of 62 dimensions out of tolerance. The agent sees that six of them are 0.04 to 0.06 mm too small in every cavity, all across the flow direction: the same pattern as mold M-1834 in the same material, where the first correction fell short and a second loop followed. It links a sink mark at the boss, in cavity 6 only, to that cavity's hot-runner nozzle, which the setting sheet shows running hotter than the others, and proposes a process change for it first. Of 13 proposed steel corrections, the designer accepts eleven, changes one and drops one, and the mold goes back to the toolroom the same day.
Your data, wherever it lives
Today the findings of a try-out sit in many places: the measurement report in the CAQ system or as a PDF, photos on the setter's phone, the setting sheet at the machine, the drawing in CAD and PLM, and the corrections of earlier molds in spreadsheets and e-mails. demi reads, understands and links them per mold, dimension and cavity, with your access rights. The AI drafts the correction list on the day of the try-out instead of someone spending half a day gathering it, and the designer decides.
Where the data lives today
- Photos, video & audio
- PDFs
- Office files
- QM system
- Machines & sensors
- CAD & drawings
- PLM
- E-mails
How demi solves it
Three layers in this order: connect the data first, then the rights, then the AI.
- 1 · ConnectData Layer
Data sources in this case: CAD, PLM, the CAQ system with the measurement reports, the molding machine's settings, photos and e-mails. demi replaces nothing and links, per mold and loop, every drawing dimension with the measured values per cavity, the photos, the process parameters and the corrections made to the steel. Every try-out then sits next to all earlier try-outs with the same material and similar geometry.
- 2 · PermitPermission Layer
Mold data and measurement reports are visible to design, toolroom, try-out and quality. Customer data such as part drawings and approvals are seen only by the project team of that mold. The responsible designer decides which corrections are made to the steel, and every correction is recorded with name and date in the mold history.
- 3 · ActIntelligence Layer
The agent reads the measurement report, assigns each value to its drawing dimension and cavity and shows every deviation against tolerance. On photos it marks typical defects such as sink marks, flash or short shots and connects them to the machine settings. Correction values are calculated by fixed rules from the measurements and the shrinkage of earlier molds; the language model only writes the reasoning.
How it runs
- 1
After the try-out, measurement report, photos and setting sheet come in from the CAQ system, the camera and the machine.
- 2
The agent assigns each measured value to drawing dimension and cavity and marks every dimension out of tolerance.
- 3
It connects defects on the photos with the process parameters and separates what the process can fix from what needs the steel.
- 4
For each dimension it shows how it behaved in earlier molds of the same material and drafts the correction list.
- 5
The designer checks, changes and releases the list; it goes to the toolroom with the mold.
What changes
The correction list is ready on the day of the try-out
Fewer correction loops before approval
What each mold teaches flows into the next one
What does it bring you?
Check it with your own numbers
Every starting value is an assumption you can change. The calculation sits right below, step by step.
Your numbers
Result
+130 hfreed per year
Assumptions and calculation
demi links CMM report, photos and settings and drafts the correction list; you decide.
3 h → 2.1 h per case
How we calculate
12 tool try-outs × 3 h × 30% × 1.0 (manual) × 12 months = 130 h
Value per year, before demi costs
Freed per year+130 h
Assumption: labor cost of $48.62 per hour in US manufacturing in June 2026 (BLS), plus workplace, IT and overhead.
= Value per year, before demi costs
+$8,450
gained per year
130 h ÷ 1,760 h per role = 0.1 full-time roles
An estimate, not a promise. The starting values are assumptions for an industrial company with 150 to 500 people.
Combine with more cases and get the packageQuestions about this use case
Does demi read reports from any coordinate measuring machine?
Yes, as PDF, spreadsheet or export file from the measuring software. The agent assigns each value to the drawing dimension by characteristic number, nominal value and cavity; if numbering is missing, it uses the ballooned drawing. If a value does not match clearly, it asks instead of guessing.
How does the agent decide between a process change and a steel correction?
By rules your toolroom sets. A dimension that deviates the same way in every cavity and barely moves with the process is a case for the steel. A defect in a single cavity, or one that shifts with holding pressure or temperature, is a case for the process first. The agent gives reasons for every proposal; the designer makes the decision.
How does demi use earlier molds for the correction?
The agent looks for molds with the same material, similar wall thickness and similar gating and shows which dimensions were corrected there, by how much, and how many loops it took. You see whether a correction fell short last time. The more try-outs demi holds, the closer the comparison.
Does the customer see the correction list?
Only if you want them to. On request, a try-out report for the customer is created with measured values, photos and the planned corrections; internal causes and comparisons with other customers' molds stay in house. The report goes out only after your release.
