Skip to content
Sales & quotingBulk Solids & Powder Handling

New powder: where did a similar one run?

demi reads the bulk solids values from the inquiry and finds plants and test-centre trials with a similar powder, compared value by value.

Today

Every inquiry brings a new powder: bulk density, flowability, particle size, moisture, dust explosion class, often an OEB level too. Whether a similar product already ran in the test centre or on a plant in the field is usually known to one or two experienced process engineers. The trial reports sit in project folders, the design in bills of materials and acceptance reports. So the powder is tested again or the plant is designed from gut feeling, and a powder that bridges shows up only at commissioning.

An example

At Dosmera a battery materials maker asks for a big bag discharge station with a screw feeder: anode graphite, bulk density 0.45 kg/l, d50 15 µm, ffc 2.1, dust explosion class St 1. The agent finds a 2021 test-centre trial with ffc 1.9 and a plant that has been running at another customer with a vibrating bottom since 2022. In the trial the powder had bridged without the vibrating bottom. The process engineer reuses the design with a vibrating bottom, and the offer goes out after two days instead of after a three-week trial.
Fictional company, typical workflow.

Your data, wherever it lives

Today powder data and experience are scattered: product data sheets in mails, test-centre reports as PDFs and spreadsheets in project folders, design and bill of materials in the PLM, acceptance and service in the ERP, and which powder causes trouble is known to two process engineers. demi reads and understands all of it and links it per plant and powder, with your rights. The AI then finds the matching trial in minutes, instead of someone searching folders or testing again, and your process engineers decide.

Where the data lives today

  • E-mails
  • PDFs
  • Folders & drives
  • Office files
  • PLM
  • ERP
  • Scans & paper
Data LayerOne view of everything, with your rights

How demi solves it

Three layers in this order: connect the data first, then the rights, then the AI.

  1. 1 · ConnectData Layer

    Data sources in this case: the mailbox, project folders, PLM, ERP and your trial reports as PDF, spreadsheet or scan. demi replaces nothing and links every plant and every test-centre trial to the customer's product, its bulk solids values, the design, the acceptance and the reports from service. So every powder sits next to the plants on which it, or a similar one, has already run.

  2. 2 · PermitPermission Layer

    URS, powder data and trials belong to the customer concerned and stay in their project room. Sales sees only that a comparable plant or trial exists, with values and result, never the customer's name or recipe. Process engineering decides what goes into the answer, and every step is recorded.

  3. 3 · ActIntelligence Layer

    The agent reads the powder values from data sheet, mail or questionnaire and compares them value by value with trials and plants: bulk density, flow function, particle size distribution, moisture, minimum ignition energy, dust explosion class. It shows the closest matches with the deviation per value, what worked back then and what did not, and which values are missing. It never promises that a powder will run on a plant; the trial or your process engineers decide that.

How it runs

  1. 1

    The inquiry arrives by e-mail with a product data sheet or questionnaire.

  2. 2

    The agent extracts the bulk solids values and flags which are missing.

  3. 3

    It searches trials and plants with similar values and shows the deviation per value.

  4. 4

    You see how the plant was designed back then and what stood out in the trial or at the customer.

  5. 5

    Process engineering decides: reuse the design, adapt it or test in the test centre.

What changes

  • Answers to powder inquiries without long searches

  • Fewer trials that were already done once

  • Difficult powders stand out before the offer

What does it bring you?

Check it with your own numbers

Every starting value is an assumption you can change. The calculation sits right below, step by step.

Assumption, editable

Your numbers

Result

+144 hfreed per year

Assumptions and calculation

demi compares each inquiry's powder values with trials and plants; your process engineers decide.

2 h → 1.4 h per case

How does it run today?

What is already digital saves less: the factor lowers the share demi brings.

How we calculate

20 powder inquiries × 2 h × 30% × 1.0 (manual) × 12 months = 144 h

Value per year, before demi costs

Freed per year+144 h

Assumption: labour cost of €49.50 per hour in German manufacturing in 2025 (Destatis), plus workplace, IT and overheads.

= Value per year, before demi costs

+€9,360

gained per year

144 h ÷ 1,760 h per role = 0.1 full-time roles

An estimate, not a promise. The starting values are assumptions for an industrial company with 150 to 500 people.

Combine with more cases and get the package

Questions about this use case

How does demi know the values of our old trials?

From your trial reports, logs and spreadsheets, scans included. The agent reads values such as bulk density, flow function or particle size with their unit and measuring method. If a measurement is missing, it shows the gap instead of an estimate.

What does similar mean for a powder?

Your process engineers set it: which values count and how far they may differ, for example bulk density, flow function, particle size, moisture and dust explosion class. The agent compares value by value and shows every deviation. It never gives a similarity score without reasons.

Does sales then see other customers' data?

No. Sales sees that a comparable plant or trial exists, with the values and the result. Customer names, URS and recipe stay in the customer's project room, and only people with rights there can open them.

Does this replace the trial in the test centre?

Not when the powder is truly new. The agent shows whether reliable trials or plants with similar values already exist and where they differ. Whether that is enough or whether you test is decided by your process engineers.

See this case with your data

In the demo we show you the workflow on your own systems.

Your configurator

No use cases yet

Your configurator is still empty

Add a use case from any card or case page and see what it brings per year, with the calculation. Free, no sign-up, no commitment: try it out and change any number.

Browse use cases