Skip to content
Warehouse, shipping & traceabilityAutomotive SuppliersAerospace

Prepreg and adhesives: out-time per roll

demi calculates the remaining out-time per roll, container and ply kit after every withdrawal and warns before expired material is laid up.

Today

Prepregs and film adhesives age at room temperature and may spend only a limited time outside the freezer. That time is written on tags on the roll, on lists at the freezer and in spreadsheets, and after a few withdrawals and shift changes everyone counts differently. Expired material in a part means scrap or a concession, and a freezer failure over the weekend often goes unnoticed.

An example

At Rennhardt Aerospace, a structural panel is due for lay-up on Tuesday; ply lay-up and vacuum bagging take two shifts. On Saturday freezer 2 fails; the agent alerts the on-call technician at once, but until the repair the freezer sits above the allowed storage temperature for nine hours. On Monday morning it shows the consequences: after four withdrawals and this failure, the planned prepreg roll has only 14 hours of out-time left. It proposes a roll of the same specification from freezer 1 with 19 days left and lists five more rolls and two adhesive films it has charged the nine hours to. Production swaps the roll, and the panel goes into the autoclave on time.
Fictional company, typical workflow.

Your data, wherever it lives

What you need for out-time is scattered today: times on tags on the roll, on lists at the freezer and in spreadsheets, lots in warehouse management and ERP, limits in the data sheet, temperatures in the freezer's logger. demi reads, understands and links them per roll and kit, with your rights. The AI calculates the remaining time right after every withdrawal and warns before expiry, and quality decides on blocked material.

Where the data lives today

  • ERP
  • MES
  • Machines & sensors
  • Office files
  • PDFs
  • Scans & paper
Data LayerOne view of everything, with your rights

How demi solves it

Three layers in this order: connect the data first, then the rights, then the AI.

  1. 1 · ConnectData Layer

    Data sources in this case: warehouse management, ERP, MES, freezer temperature loggers, data sheets and spreadsheets. demi replaces nothing and links every roll and container with lot, storage life and allowed out-time, with each withdrawal, thaw time and return, with the kits cut from it and the production orders up to the start of cure. Every roll gets a complete history.

  2. 2 · PermitPermission Layer

    Stores, cutting and lay-up book withdrawals and returns, and everyone who processes the material sees the remaining time. Only quality releases blocked material, and every extension or concession is recorded with name and test result.

  3. 3 · ActIntelligence Layer

    The agent calculates the times with fixed rules from the booked events and the data sheet limits; nothing is estimated. It matches them against the production plan, warns before expiry and proposes another roll or sequence. The language model reads data sheets and voice messages and explains each warning; the rules do the arithmetic.

How it runs

  1. 1

    At goods receipt, every roll and container gets lot, storage life and allowed out-time from certificate and data sheet.

  2. 2

    Withdrawals, thawing, returns and cut kits are scanned or reported by voice.

  3. 3

    The agent calculates the used and remaining time per roll, kit and part, freezer failures included.

  4. 4

    If the remaining time is too short for a planned order, it proposes another roll or sequence in good time.

  5. 5

    It blocks expired material until quality decides on scrap, retest or concession.

What changes

  • Expired material is blocked before it goes into a part

  • Less scrap and fewer concessions

  • Remaining times without tags and hand calculation

What does it bring you?

Check it with your own numbers

Every starting value is an assumption you can change. The calculation sits right below, step by step.

Assumption, editable

Your numbers

Result

+160 hfreed per year

Assumptions and calculation

demi calculates out-time per roll from every withdrawal and warns before expiry; you replan or use it.

8 min → 4 min per case

How does it run today?

What is already digital saves less: the factor lowers the share demi brings.

How we calculate

200 rolls and containers × 8 min × 50% × 1.0 (manual) × 12 months = 9,600 min = 160 h

Value per year, before demi costs

Freed per year+160 h

Assumption: labour cost of €49.50 per hour in German manufacturing in 2025 (Destatis), plus workplace, IT and overheads.

= Value per year, before demi costs

+€10,400

gained per year

160 h ÷ 1,760 h per role = 0.1 full-time roles

An estimate, not a promise. The starting values are assumptions for an industrial company with 150 to 500 people.

Combine with more cases and get the package

Questions about this use case

How do withdrawal times reach demi?

By a scan at the freezer, through the booking in warehouse management or by a voice message at the freezer, for example that roll 4471 is going to cutting. Every message is recorded with time and person in the roll's history. If a return is missing, the agent asks instead of counting the roll as frozen.

What happens when a freezer fails?

The agent reads the freezers' temperature loggers. If a freezer sits above the allowed storage temperature, it charges the time to every roll stored in it according to its location and reports which rolls, kits and orders are affected.

Does demi also count the time of cut plies and kits?

Yes. Kits inherit the out-time of their roll, and the clock runs until the start of cure. If a part's plies come from several rolls, the shortest remaining time applies. Kits that go back into the freezer keep the time they have used.

Can expired material be released again?

Only by the procedure in your specification, for example after retesting gel time and resin flow, or through a concession. The agent compiles the data and the test request. Decision and signature stay with quality.

See this case with your data

In the demo we show you the workflow on your own systems.

Your configurator

No use cases yet

Your configurator is still empty

Add a use case from any card or case page and see what it brings per year, with the calculation. Free, no sign-up, no commitment: try it out and change any number.

Browse use cases