Skip to content
Sales & quotingPumps & ValvesElectronics & SensorsWater & EnvironmentMachinery & Plant Engineering+4

Total cost of ownership and savings for your customer

Show your customer what your product saves over the years: energy, maintenance and payback, calculated from their own operating data.

Today

Your product costs more to buy but saves energy and maintenance over the years. Yet the quote only shows the purchase price, because a proper total cost calculation takes application engineering days: finding curves, asking the customer for operating data, estimating maintenance, putting it all into a spreadsheet. So the customer's purchasing department decides on price.

An example

A water supply association is replacing a pump in its pumping station and has so far compared two quotes on purchase price alone. Hartwig & Brunn Pumpenwerk offers a KP DN 100 with an IE4 motor, 4,200 euros more than a competitor's pump with an IE3 motor. The association sends last year's operating data as a spreadsheet: 6,000 hours, mostly around 110 m³/h. The agent places this duty point on both curves, Hartwig & Brunn's from the PLM and the competitor's from its published data sheet: there the KP DN 100 runs at 80% efficiency, the other pump at 73%. That is about 20,000 kWh less per year, around 4,000 euros at 20 cents per kWh. The agent sets maintenance equal for both and marks this as an assumption, because there is no service data for the other pump. The extra price is paid back in just over a year, and over 15 years the difference exceeds 50,000 euros. Application engineering checks the duty points, sales approves, and the calculation goes to the association with the quote.
Fictional company, typical workflow.

Your data, wherever it lives

What your product saves over the years is scattered today: curves and data sheets in the PLM, maintenance intervals and spare part prices in the ERP, call-outs to similar installations in the service history, the customer's operating data in a spreadsheet somewhere in a mailbox. demi reads, understands and links them, with your rights. The calculation over the whole service life is ready in an hour instead of two days, and you decide what the customer gets to see.

Where the data lives today

  • Office files
  • Machines & sensors
  • PLM
  • ERP
  • CRM
  • E-mails
Data LayerOne view of everything, with your rights

How demi solves it

Three layers in this order: connect the data first, then the rights, then the AI.

  1. 1 · ConnectData Layer

    Data sources in this case: the customer's spreadsheets and operating data, PLM, ERP, CRM and e-mail. demi replaces nothing and joins performance curves and data sheets, maintenance intervals, spare part prices and the service history of similar installations with the customer's operating data into one calculation per quote.

  2. 2 · PermitPermission Layer

    The customer's operating data and energy prices are visible only to the team that looks after them. Internal costs and margins never flow into the customer document. The calculation goes out only after application engineering and sales have approved it, and the approval is recorded.

  3. 3 · ActIntelligence Layer

    The agent places the customer's duty points on your curves and calculates energy, maintenance and spare parts per year with fixed formulas, plus total cost, savings and payback. Every assumption is visible and can be changed. The language model does not calculate; it explains the result in words the customer's purchasing department understands.

How it runs

  1. 1

    The customer sends a load profile, meter readings or operating hours, or they come straight from the installed unit.

  2. 2

    The agent sets up the comparison: your offer against the existing unit or a competitor product as per its data sheet.

  3. 3

    It calculates energy, maintenance and spare parts per year from curves, service history and the customer's energy price.

  4. 4

    Total cost, savings and payback sit in one document, every assumption visible and adjustable.

  5. 5

    Application engineering and sales check and approve, then the calculation goes out with the quote.

What changes

  • Quotes win on lifetime cost, not purchase price alone

  • Every figure backed by a curve, a measured value or a stated assumption

  • Cost of ownership in hours instead of days

What does it bring you?

Check it with your own numbers

Every starting value is an assumption you can change. The calculation sits right below, step by step.

Assumption, editable

Your numbers

Result

+307 hfreed per year

Assumptions and calculation

demi calculates energy, maintenance and payback from curves and customer data; you check and approve.

16 h → 9.6 h per case

How does it run today?

What is already digital saves less: the factor lowers the share demi brings.

How we calculate

4 cost of ownership calculations × 16 h × 40% × 1.0 (manual) × 12 months = 307 h

Value per year, before demi costs

Freed per year+307 h

Assumption: labour cost of €49.50 per hour in German manufacturing in 2025 (Destatis), plus workplace, IT and overheads.

= Value per year, before demi costs

+€19,955

gained per year

307 h ÷ 1,760 h per role = 0.2 full-time roles

An estimate, not a promise. The starting values are assumptions for an industrial company with 150 to 500 people.

Combine with more cases and get the package

Questions about this use case

Where does the customer's operating data come from?

From whatever they have: a load profile, meter readings, operating hours from the control system or an on-site measurement, usually as a spreadsheet by e-mail. If your unit at the customer's site sends data, demi takes it directly. If something is missing, the agent calculates with a marked assumption and notes what it still needs from the customer.

Can I include a competitor product in the comparison?

Yes, based on published data sheets and curves, every value with its source. The agent compares only verifiable values and marks where it would have to estimate. Whether the competitor is named in the customer document is up to sales.

Who calculates the figures in the cost of ownership calculation?

Fixed formulas, not estimates by the language model: power times operating hours times energy price, plus maintenance and spare parts from your data. Every result can be recalculated with the same values. The language model only explains where the difference comes from.

What does the customer see, and what stays internal?

The customer gets the comparison, assumptions and sources in one document in your layout. Internal costs, margins and your costing bases stay internal. The document goes out only after approval.

See this case with your data

In the demo we show you the workflow on your own systems.

Your configurator

No use cases yet

Your configurator is still empty

Add a use case from any card or case page and see what it brings per year, with the calculation. Free, no sign-up, no commitment: try it out and change any number.

Browse use cases