Skip to content
Planning & productionPlastics & PackagingTool & Mould MakingAutomotive SuppliersMedical Technology

Setting sheets from paper back to the machine

demi reads setting sheets from the tool cabinet and shows, for each mould and machine, the setting that last produced good parts.

Today

For many injection moulds a paper setting sheet hangs in the tool cabinet, with crossings-out and notes such as “holding pressure +20 bar, sink marks gone”. The data set on the machine is often a different version, and when the mould runs on another machine, neither fits. So every start-up begins with trial and error, with scrap and with a call to the one setter who remembers.

An example

At Polivo Kunststoffverpackungen the 32-cavity mould for the VS-38 closure is due to restart after eleven weeks, this time on machine 14 instead of machine 9. The tool cabinet holds four setting sheets with handwritten corrections, the machine a data set from 2023. The agent shows that the June run was the best, with 0.4 % scrap: holding pressure 30 bar higher than on the sheet, cooling time 0.3 s shorter, noted by hand with “sink marks gone”. It converts metering stroke and pressures to the larger screw of machine 14, and the setter has good parts after 25 minutes; the last start-up took two hours.
Fictional company, typical workflow.

Your data, wherever it lives

Good settings live today on paper sheets in the tool cabinet, as data sets on individual machines and USB sticks, as process data in the MES and as experience in the setters' heads, apart from scrap and inspection results in the QMS. demi reads, understands and links them per mould, machine and material, with your rights. The AI shows the last good setting in seconds before every start-up, and the setter decides at the machine what to apply.

Where the data lives today

  • Scans & paper
  • Machines & sensors
  • MES
  • QM system
  • ERP
Data LayerOne view of everything, with your rights

How demi solves it

Three layers in this order: connect the data first, then the rights, then the AI.

  1. 1 · ConnectData Layer

    Data sources in this case: scanned setting sheets from tool cabinets and binders, data sets from the machine controls, process data and scrap from the MES, inspection results and defect records from the QMS and the order history from the ERP. demi replaces nothing and joins everything into one record per mould, machine and material. You see every run with its setting, result and note.

  2. 2 · PermitPermission Layer

    Setting data are visible to setters, shift leads and process engineering; data of customer-owned moulds stay with that customer's team. demi writes nothing into a machine control. A new standard data set is released by process engineering, for validated processes through your change procedure, and that is logged.

  3. 3 · ActIntelligence Layer

    The agent transfers values and handwritten corrections into fields, unifies units and links every run with scrap and defect records. It shows the setting that last produced good parts and explains how it differs from other versions. Conversions to another machine follow fixed formulas from screw diameter and pressure ratio and are marked as a proposal.

How it runs

  1. 1

    Setting sheets from tool cabinets and binders are scanned; machine data sets and MES process data are connected.

  2. 2

    demi reads every sheet including handwritten corrections and assigns it to mould, machine, material and date.

  3. 3

    For each run the agent links setting, scrap, defect records and inspection results.

  4. 4

    Before the next start-up it shows the setting that last produced good parts and converts it to another machine if needed.

  5. 5

    The setter applies the values at the machine, and process engineering releases the new version as a data set.

What changes

  • Start-ups begin with the last good setting instead of trial and error

  • Less start-up scrap and shorter changeovers

  • Setters' knowledge stays in the plant, across shifts and years

What does it bring you?

Check it with your own numbers

Every starting value is an assumption you can change. The calculation sits right below, step by step.

Assumption, editable

Your numbers

Result

+120 hfreed per year

Assumptions and calculation

demi shows the last good setting for each mould and machine; the setter applies it at the machine.

40 min → 28 min per case

How does it run today?

What is already digital saves less: the factor lowers the share demi brings.

How we calculate

50 mould start-ups × 40 min × 30% × 1.0 (manual) × 12 months = 7,200 min = 120 h

Value per year, before demi costs

Freed per year+120 h

Assumption: labour cost of €49.50 per hour in German manufacturing in 2025 (Destatis), plus workplace, IT and overheads.

= Value per year, before demi costs

+€7,800

gained per year

120 h ÷ 1,760 h per role = 0.1 full-time roles

An estimate, not a promise. The starting values are assumptions for an industrial company with 150 to 500 people.

Combine with more cases and get the package

Questions about this use case

Can demi read handwritten setting sheets?

Yes, from a scan or a phone photo. demi recognises the values in the form fields, crossings-out and margin notes and marks handwritten corrections as such. If a digit is not clearly legible, such as a 1 or a 7, the agent shows the cut-out and asks.

Where do the machine data sets come from?

From the machines' data set storage, from the MES or from the drive where your setters keep them. How the data reaches demi, we clarify in conversation. For older machines without an interface, a photo of the setting screens is enough.

Does demi set up the machine itself?

No. demi writes nothing into a machine control; the setter applies the values. Process engineering releases a new standard data set, and for validated processes, for example in medical technology or for automotive customers, every change goes through your change procedure.

How does demi know which setting was good?

From the result of the run: scrap from the MES or ERP, inspection results and defect records from the QMS, complaints about the lot. The agent shows what went well and badly in each run. What counts as good, such as a scrap limit or no complaint, you define.

See this case with your data

In the demo we show you the workflow on your own systems.

Your configurator

No use cases yet

Your configurator is still empty

Add a use case from any card or case page and see what it brings per year, with the calculation. Free, no sign-up, no commitment: try it out and change any number.

Browse use cases